Whoa! You can't buy your own item.

Star Wars Inspired ID9 Seeker Droid 3D Model

Instant download

Description

**These files are not for distribution or for selling kits/parts. Please read my Policies & FAQ before purchasing. Thank you for your support!**

Heads up!!! This is very different from the new Battlefront 2 ID10 droid. Please make sure of which droid you need before purchasing!


This the 3D model I created from scratch of the ID9 Seeker Droids the Seventh Sister uses. Here is a link to my blog post with some exploded views of him: http://keltaria.com/2017/11/id9-seeker-droid-seventh-sister/

This file contains ten (10) .STL files meant for 3D printers. Please read the points below before purchasing and contact me with any questions! =)

Some points:
- These files produce the basic parts for the droid. All his appendage segments are separate for you to pose him how you want.
- XTC3D is awesome. I use that to smooth out a lot of my prints (but be careful applying it!). Go lightly and gradually to reduce drippage on curved parts. Coat & sand = so smooth! File off the bumps/drips.
- The top and bottom of his eye-hole are the thinnest parts of the print, it may even be spotty depending on your print settings. With a coating of XTC3D and paint, it covers it up quite nicely.
- There is an area for a basic tealight (I found remote control ones, they are kinda awesome!). If you are an electrical wizard then by all means use other types of lights/LEDs.
- Attach the legs as you see fit. I used brass rods and superglue.
- There are indentations for small magnets on the bottom piece and washers on the top (please note this is not as strong as I like it with what I'm currently using, BUT I'll be holding him from the bottom so I'm not too concerned).
- I used an acrylic rod for his antenna and scrap ABS for his flag. Depending what you find it may fit right in the existing hole or file it open a bit.
- Always be careful with your little droid. One good whack and the legs will likely still pop off/come loose.

Please see the images for this listing for samples of the 3D files and how they are laid out for printing. I even provided extra hands/feet for other options! =)

List of files:
Droid Bottom HEAD v2.2
Droid Top HEAD v2.2
Droid Inner HEAD v2.2
Droid ARM A v2.2
Droid ARM B v2.2
Droid HANDS extra v2.2
Droid LEG A v2.2
Droid LEG B v2.2
Droid LEG C v2.2
Droid FEET extra v2.2
**These files are not for distribution or for selling kits/parts. Please read my Policies & FAQ before purchasing. Thank you for your support!**

Heads up!!! This is very different from the new Battlefront 2 ID10 droid. Please make sure of which droid you need before purchasing!


This the 3D model I created from scratch of the ID9 Seeker Droids the Seventh Sister uses. Here is a link to my blog post with some exploded views of him: http://keltaria.com/2017/11/id9-seeker-droid-seventh-sister/

This file contains ten (10) .STL files meant for 3D printers. Please read the points below before purchasing and contact me with any questions! =)

Some points:
- These files produce the basic parts for the droid. All his appendage segments are separate for you to pose him how you want.
- XTC3D is awesome. I use that to smooth out a lot of my prints (but be careful applying it!). Go lightly and gradually to reduce drippage on curved parts. Coat & sand = so smooth! File off the bumps/drips.
- The top and bottom of his eye-hole are the thinnest parts of the print, it may even be spotty depending on your print settings. With a coating of XTC3D and paint, it covers it up quite nicely.
- There is an area for a basic tealight (I found remote control ones, they are kinda awesome!). If you are an electrical wizard then by all means use other types of lights/LEDs.
- Attach the legs as you see fit. I used brass rods and superglue.
- There are indentations for small magnets on the bottom piece and washers on the top (please note this is not as strong as I like it with what I'm currently using, BUT I'll be holding him from the bottom so I'm not too concerned).
- I used an acrylic rod for his antenna and scrap ABS for his flag. Depending what you find it may fit right in the existing hole or file it open a bit.
- Always be careful with your little droid. One good whack and the legs will likely still pop off/come loose.

Please see the images for this listing for samples of the 3D files and how they are laid out for printing. I even provided extra hands/feet for other options! =)

List of files:
Droid Bottom HEAD v2.2
Droid Top HEAD v2.2
Droid Inner HEAD v2.2
Droid ARM A v2.2
Droid ARM B v2.2
Droid HANDS extra v2.2
Droid LEG A v2.2
Droid LEG B v2.2
Droid LEG C v2.2
Droid FEET extra v2.2

Reviews

5 out of 5 stars (22)

Downloads

File delivery
Your files will be available to download once payment is confirmed. Here's how.

Payment options

Secure options
Paypal Visa Mastercard American Express Discover Giftcard
Accepts Etsy Gift Cards and Etsy Credits
Etsy keeps your payment information secure. Etsy shops never receive your credit card information.

Returns & exchanges

I don't accept returns, exchanges, or cancellations

But please contact me if you have any problems with your order.

FAQs

Most models should be able to scale easily within your printer's software.
Please ask if you'd like anything customized. Additional design fees may apply.

Please note I will likely not customize parts of an existing model, but suggestions to one are welcome. You are more than welcome to ask though as it may depend what you want done.
No, these are for your personal use only.
No, as I offer kits here and there myself.
For a kit request:
1. Please click on the Request Custom Order button on my shop to the left. I'll let you know a time frame, especially if I already have orders in queue. Most orders will ship via a USPS Med Rate Box. You can also check the Announcement section of my shop for a timeframe.
2. Once I have availability I'll create a private listing and you'll get an e-mail that your request is ready to be ordered.
3. When I get confirmation of the order, I'll start printing! =)