Poker Table Art Piece for Glowforge - SVG - PDF - Multi-layer - Digital File

This purchase is for a digital file. This file is formatted for a Glowforge laser engraving of a multi-layered Poker Table which measures 9.5" in height and 18.5" in width. This is not for a physical product.

This multi-layered Poke Table is glued together and can be custom built to suit your needs.
Pictures attached are made from 1/4" mahogany, walnut, and maple plywood.

This design was so much fun to create. I wanted to make a product that could be customized to the max, so it's easy to mix and match types of wood or paint to make a very impressive effect. I look forward to seeing other finished products.

Unzip first file and you will see all the individual layers for cutting inside.
This file was created on Adobe Illustrator and is saved as an (.AI) and (.PDF) (.DXF) and (.SVG).

You may use this file for personal or commercial finished projects, but do not share or resell any part of this file.


All layers were masked first before engraving and cutting, then painted.


Layer 1: Cards - Each card measures 2.1" high and 1.4" wide. Cards were made out of 1/4" maple plywood.
-Each card was engraved with a setting of "SD Graphic" (Speed 535, Power 70, LPI 270). Additional cards can also be purchased as a separate file on my Etsy Store but will have to be re-sized.

Layer 2: Main Table - The main green table measures 18.5" wide and 9.5" high. The table was made out of 1/4" maple plywood. I have separated the table into a couple colors to shorten engrave time.
-Both the "Vegas Skyline" and the "Poker Texas Hold'em" were engraved with a setting of "SD Graphic" (Speed 535, Power 70, LPI 270).

Layer 3: Outer Ring - I have 3 ring layers that sit above the Main Table. This is the wider layer that is painted white in the pictures. Only 1 layer of this needs to be cut.

Layer 4 & 5: Outer Ring - Both layers are the outer ring that sit above layer 3. I painted the top layer black to illustrate the leather arm rests at an actual table. I tried to texture this layer by sprinkling water spots before spray-painting in order to make the table look a bit older.

Layer 6, 7, 8, 9, 10: Poker chips 100, 500, 1000, 5,000 and 10,000 - This is really where you get to custom fit your own layout. For my photos I only used the first 3 numbers but I have included additional chip numbers in case you wish to personalize as desired. I had cut these chips from different types of wood as I originally thought I was not going to paint the whole board. All chips were made from 1/4" plywood. Each chip was engraved with a setting of "SD Graphic" (Speed 535, Power 70, LPI 270). The amount of chips you cut will be custom to your own board. I had cut additional chips with setting the number part to "ignore" in order to only create the outer ring. This gave me the added effect of higher chip piles but not actually cutting tons of chips. Each chip measures about 3/4" in diameter.

Layer 11: Back of Card - This is where I custom built the back of the card to reflect my own initials (a small personalized hidden egg). This player card was also made out of 1/4" maple plywood. Each card was scored with a setting of "Score - Draft" (Speed 300, Power 30). Each card measures 2.1" high and 1.4" wide.

Layer 12: Blank Card - This was used to raise the dealer deck in order to give it the "more cards look" without actually scoring multiple cards. Each card measures 2.1" high and 1.4" wide.

Layer 13: Dealer Button - This was also made from 1/4" plywood and engraved with a setting of "SD Graphic" (Speed 535, Power 70, LPI 270). The dealer button measures 1" in diameter.



Enjoy.