Whoa! You can't favorite your own shop.

Whoa! You can't buy your own item.

Whoa! You can't favorite your own item.

Whoa! You can't add your own item to a list.

Add this item to a treasury!

Close
You don't have any treasuries yet. Enter a title below to create one.
Close

This item has been added.

View your treasury.

Like this item?

Add it to your favorites to revisit it later.
Request a custom order and have something made just for you.
THIS IS NOT A FULL GHOST TRAP PEDAL - THIS IS ONLY ASSEMBLY HARDWARE SHOWN IN FIRST PICTURE - YOU MUST 3D PRINT THE REST OF THE PARTS!

I designed a Ghost Trap that can be 3D printed - you must print all your own parts such as body panels, knobs, doors, etc - I am selling the nuts, bolts, screws, etc to put it all together. You receive only the parts shown in picture #1 above.

If you have access to a 3D printer - download and print the parts for my Ghost Trap Pedal design:
http://www.thingiverse.com/thing:1394639

See fully illustrated assembly guide here: www.charlesworth-dynamics.com/2013/08/instructions.html
It's a good idea to take a look before you buy so you know what you're getting into.

This is also valuable for those already scratch building their own pedals as these are movie-accurate parts.

This kit is includes only the following:

- Over 30 screws for assembly
- Rubber feet for base
- Hinge for pedal - this exactly lines up with the 3D printed model
- Ribbon cable and cable ties used as handle
- Red and yellow pneumatic tubing
- Rigid hose used for pedal bellows
- High-strength neodymium magnet for 3D printed male Foster hose connector
- Electronic Relay - the relay is the clear rectangular box with electronics in it mounted to the left side. The movie original relay is an ITT relay which I have not been able to find at a reasonable price. I am offering substitutes that are very close. The 11 pin socket will need printed from the 3D files I released.

- Extras of most parts are included for those who (like myself) WILL drop and lose something

This is ONLY the hardware shown in the first picture, 3D printed Pedal and 3D printed parts are not included and must be printed elsewhere.

A Deluxe Hardware Upgrade kit can be combined with this kit to add even more real hardware, such as side boxes, computer connectors, relay socket, etc: http://etsy.me/223d7Qb

You can also add a Hose for connecting to Ghost Trap: http://etsy.me/24R8zP8

Pictures are of a fully 3D printed Pedal assembled with hardware kit.

Learn more about how the Trap and Pedal were built on Tested.com:
http://bit.ly/1LRt73B

Frequently asked questions about CharlesworthDynamics

3D printed objects are made by 'slicing' a digital model into many thin layers. These slices are sent to a printer that 'draws' each layer by extruding plastic through a hot nozzle.
There are a lot of different materials available now but the two most common are ABS (LEGO plastic) and PLA (biodegradable plastic) which is what Charlesworth Dynamics uses.
While the 3D prints aren't hazardous, they are not food, dishwasher or microwave safe.
They are very strong, but will break just like any plastic item if abused.
3D prints are very strong if printed properly but will break just like any plastic item if abused. Since the object is printed in layers, they will have a slightly ridged texture to them unlike a injection molded object. There is usually a 'zipper' which is a slight vertical seam that indicates where each new layer starts. They may have slight defects or blemishes and the bottom which adheres to the print bed may have some discoloration. Kit pieces may need minor clean up or trimming to fit together. This is typical of most 3D prints.
Yes, you can sand and paint 3D prints like a normal plastic model. You can even use products like Bondo Glazing and Spotting putty to minimize and smooth the 3D printed texture. Make sure to use a plastic-friendly paint.
I include a link for assembly instructions with your shipping notification, but here's a link for all assembly guides:
charlesworth-dynamics.com/2013/08/instructions.html

Please don't hesitate to contact me with any questions or recommendations.
On occasion I will also build items out of 'real' parts and hardware - typically I use vintage Film & TV equipment parts. I have made lamps out of old lenses and jewelry out of old camera parts. Keep in mind that these are all used parts and will show their wear and tear and age - it's part of their charm.

Trap Pedal Standard Hardware Kit

$38.00

Overview

  • Handmade Supply
  • Made to order
  • Ships worldwide from United States
  • Feedback: 134 reviews
  • Favorited by: 47 people