Whoa! You can't buy your own item.

Orgone Casting Pyramid Mold, 90 X 90mm Base, Self-Lubricating Polyethetlene, Golden Proportions of Pyramid of Giza

Like this item?

Add it to your favorites to revisit it later.
Favorite
Request a custom order and have something made just for you.

Description

This listing is for one Pyramid Mold that have Golden section of Giza Pyramid, made out of 5mm polyethylene 500 (HDPE) self-lubricating plastic.

About the MOLD:

This mold will be shipped flat, and in order to prepare the mold for casting you will need to close one open edge with scotch tape.
When you casting has cured, we recommend un-taping the mold and removing the casting this way, in order to avoid any possible damages to the edges of your casting.
When you remove your casting you can clean the mold with soft wipe soaked with acetone,it will nort effect your mold in any way, but will clean your mold ready for your next casting.

For best results, we recommend:

Use small amount of resin and perform pre-glazing your mold before you star casting your actual design. Mix small amount of resin and pour it into your mold,
start tilting your mold in a way that allows you to cover with resin all internal walls, we recommend doing this procedure 2-3 times for best results.
This pre-glazing technique is well known to produce very nice and smooth casting walls, giving your work much more appealing to the aye pyramid

If you like to take it one step further then you can light sand your casting with sandpaper water grades 2000, 2500, 3000, then you finish your casting on sponge polishing pad mounted on drill
or motor (ideally car polishing machine) with some car polishing compound you will be able to get very much mirror like finish.

About HDPE:

Very low co-efficient of friction
Very high surface release properties
High chemical resistance
Excellent impact resistance
Very good damping properties
Weldable plastic
Excellent abrasion resistance

Applications:
Resin Casting molds
Flow promoting liners to resist sliding abrasion and assist release.
Conveyor components subject to high wear and requiring low friction.
Componentry in direct contact with food stuffs.
Parts subject to high impact stresses.

About MOLD GEOMETRY:

This mold has golden ratio in proportions that the Great Pyramid of Giza has.
Sacred mean (Phi), was also recorded into the dimensions of the pyramid itself.
The exterior angle of the 'Great pyramid of Giza' can be reproduced with the Vesica-pisces. It has been long suspected that the Great pyramid was a subsidiary of geometric knowledge. There are several other indications that sacred geometry was an important factor in the design of the pyramid.

Dimensions:

As shown on the picture above.


Thanks for reading and happy casting :)
Phi Molds
This listing is for one Pyramid Mold that have Golden section of Giza Pyramid, made out of 5mm polyethylene 500 (HDPE) self-lubricating plastic.

About the MOLD:

This mold will be shipped flat, and in order to prepare the mold for casting you will need to close one open edge with scotch tape.
When you casting has cured, we recommend un-taping the mold and removing the casting this way, in order to avoid any possible damages to the edges of your casting.
When you remove your casting you can clean the mold with soft wipe soaked with acetone,it will nort effect your mold in any way, but will clean your mold ready for your next casting.

For best results, we recommend:

Use small amount of resin and perform pre-glazing your mold before you star casting your actual design. Mix small amount of resin and pour it into your mold,
start tilting your mold in a way that allows you to cover with resin all internal walls, we recommend doing this procedure 2-3 times for best results.
This pre-glazing technique is well known to produce very nice and smooth casting walls, giving your work much more appealing to the aye pyramid

If you like to take it one step further then you can light sand your casting with sandpaper water grades 2000, 2500, 3000, then you finish your casting on sponge polishing pad mounted on drill
or motor (ideally car polishing machine) with some car polishing compound you will be able to get very much mirror like finish.

About HDPE:

Very low co-efficient of friction
Very high surface release properties
High chemical resistance
Excellent impact resistance
Very good damping properties
Weldable plastic
Excellent abrasion resistance

Applications:
Resin Casting molds
Flow promoting liners to resist sliding abrasion and assist release.
Conveyor components subject to high wear and requiring low friction.
Componentry in direct contact with food stuffs.
Parts subject to high impact stresses.

About MOLD GEOMETRY:

This mold has golden ratio in proportions that the Great Pyramid of Giza has.
Sacred mean (Phi), was also recorded into the dimensions of the pyramid itself.
The exterior angle of the 'Great pyramid of Giza' can be reproduced with the Vesica-pisces. It has been long suspected that the Great pyramid was a subsidiary of geometric knowledge. There are several other indications that sacred geometry was an important factor in the design of the pyramid.

Dimensions:

As shown on the picture above.


Thanks for reading and happy casting :)
Phi Molds

Reviews

5 out of 5 stars
(489)

Payments

Secure options
  • Visa
  • Mastercard
  • American Express
  • Discover
  • Paypal
  • GiftcardAccepts Etsy Gift Cards and Etsy Credits
Etsy keeps your payment information secure. Etsy shops never receive your credit card information.
Payment is accepted via PayPal.

Your order will be processed when payment is cleared. Please be aware that if you pay by E-Check via PayPal, it takes time for the payment to clear .

If payment hasn't been made within 5 days of placing an order, with no -email correspondence, I would cancel the order.

Returns & exchanges

If you receive your item and you are not 100% happy with it please get in touch ASAP so we can resolve the issue in the best manner possible.
I never ask questions before I give you full money refund, If my client think he is right, I will not argue, for me THE CLIENT IS ALWAYS RIGHT!

Shipping policies

All items will be packed and shipped on the same or next day after receipt of payment, except on Saturdays, Sundays and local holidays. All items are shipped gently/carefully and safely with Priority Mail. All purchases will have tracking number.

Please notice that shipment to USA and Canada usually take 10 or more working days and even longer before holidays like Christmas, please be aware that possible delays are beyond my control. Payment with e-check will add 4-6 more days to shipping time.

I always set my parcels value of 1 USD so you dont have to go thru customs in order to get your item.

Orgone Casting Pyramid Mold, 90 X 90mm Base, Self-Lubricating Polyethetlene, Golden Proportions of Pyramid of Giza

Ask a question

$10.28

Please select a quantity

Overview

  • Handmade item
  • Material: HDPE
  • Made to order
  • Feedback: 489 reviews
  • Favorited by: 25 people
  • Gift message available
This shop accepts Etsy gift cards

Shipping & returns

Ready to ship in 1–2 business days
From Bulgaria

What’s wrong with this listing?

The first thing you should do is contact the seller directly.

If you’ve already done that, your item hasn’t arrived, or it’s not as described, you can report that to Etsy by opening a case.

Report a problem with an order

We take intellectual property concerns very seriously, but many of these problems can be resolved directly by the parties involved. We suggest contacting the seller directly to respectfully share your concerns.

If you’d like to file an allegation of infringement, you’ll need to follow the process described in our Copyright and Intellectual Property Policy.

Review how we define handmade, vintage and supplies

See a list of prohibited items and materials

Read our mature content policy

The item for sale is…