Complete Mesh Node Mini | Meshtastic | Meshcore | Heltec v4 GPS 3000mah LiPo | 915mhz LoRa Wifi & Bluetooth | Off Grid Communication Device

Fully assembled and ready-to-use 915MHz LoRa handheld mesh node built with the Heltec V4 ESP32 platform, housed in a durable PETG enclosure and powered by a 3000mAh rechargeable battery. Compatible with both Meshtastic and MeshCore, this device arrives fully flashed(choose Meshtastic or Meshcore at checkout), assembled, and tested — no setup, soldering, or firmware installation required.

Simply charge, pair with your phone over Bluetooth, and start communicating off-grid.

---------------------

What’s Included:

1x Fully assembled handheld node
1x Quick-Start guide &
+ Online access to support files and tutorials.
**Optional**
1x GPS module add-on
1x 17cm Whip Antenna Upgrade (in addition to factory antenna)

Specifications:

Hardware: Heltec V4 LoRa Wifi BLE board
Antenna: Factory 2dbi antenna
Frequency: 915MHz LoRa (US region)
Charging: USB-C
Battery: 3000mAh rechargeable lithium battery
Display: onboard OLED screen
Case Material: PETG printed enclosure
Compatibility: Meshtastic + MeshCore
Dimensions: 75mm x 60mm x 25mm
Dimensions w/Antenna: 110mm x 60mm x 25mm
Status: fully assembled, flashed, and tested

---------------------

What is Meshtastic / MeshCore?

Meshtastic and MeshCore are off-grid communication platforms that allow devices to send messages using LoRa mesh radio instead of cellular service or internet.
Each device acts as a node, meaning it can:

-send messages
-receive messages
-relay messages for other nodes
-extend overall network range

Great for:

-camping
-hiking
-emergency preparedness
-events
-remote property use
-off-grid travel

---------------------

Off-Grid Communication:

Off-grid communication means sending messages without relying on cell towers, Wi-Fi, or internet service.
As long as there are other compatible nodes nearby, messages can travel from device to device through the mesh network.
This makes it extremely useful in low-signal areas or emergency situations.

---------------------

About the PETG Enclosure:

This case is professionally 3D printed in PETG, a material chosen for its durability and outdoor suitability.

Compared to PLA, PETG offers:

-better heat resistance
-improved toughness
-better impact resistance
-improved long-term durability

Ideal for portable outdoor use.

---------------------

Battery Life & Care:

Battery life depends on usage, relay traffic, screen brightness, and GPS use.

Typical runtime is around 24 hours, typical with ESP32 devices.

For best battery health:

-charge via USB-C
-avoid long-term storage while fully drained
-keep away from extreme heat
-recharge occasionally during long storage periods

---------------------

Ready Out of the Box

This device is fully ready to use on arrival.
No flashing, no assembly, and no technical setup required.
Just charge it, pair it to the app, and start meshing!

---------------------

Important Information & Disclaimer

This is a functional electronic communication device intended for use with Meshtastic and/or MeshCore software platforms.

All devices are:

-fully assembled
-tested before shipment
-verified functional prior to packaging

Because of the nature of programmable/open-source hardware, users may choose to modify firmware, settings, or device behavior after delivery.

Please note:

Returns are not accepted for devices that have been reflashed, modified, disassembled, physically damaged, or improperly configured after delivery.
Devices damaged due to incorrect charging methods, improper battery handling, flashing errors, or user modification are not covered.
Minor firmware configuration differences between Meshtastic and MeshCore may occasionally require user adjustment or firmware updates.
Technical familiarity with community-driven/open-source platforms is helpful when using advanced features.

If you experience an issue, please contact us before attempting repairs or modifications. I’m happy to help troubleshoot and provide guidance whenever possible.