Compound Bow Hanger Hub Blind | Silent Bow Hook | Drop-On Bow Holder | Fits Ameristep Primos Rhino Muddy | USA Made

**A drop-on compound bow hanger that installs on your hub blind's ceiling poles in twenty seconds. Wide center hook holds any bow — solid limb or split-limb — by the string, cam, or laid flat across both limbs. Two small side stubs hold your release aid, hat, or a paracord loop. Silent to install, silent to remove.**

You're set up in the blind. You've been holding your bow for two hours because there's nowhere to put it down that isn't the floor or the fabric wall. Your arm is fatigued. When the shooter comes into range, you're already fighting a shake you didn't have at first light.

**This solves that.** A 3.9-inch center hook takes the bow — string, upper cam, or laid flat across both limbs on split-limb bows like the Hoyt RX-10. Keeps the riser off the floor, keeps the sight glass clean, keeps the quiver upright. The whole rig hangs on ONE hook that drops onto the top-downward hub poles of your blind. Zero hardware.

**Split-limb ready.** The 3.9-inch center hook length catches BOTH parallel limbs of split-limb compound bows — Hoyt RX/RX-10 series, Bowtech Reckoning, PSE Evoke, Elite, and every modern hunting split-limb setup. Both limbs lay flat across the hook, weight is distributed evenly, bow sits square.

**Silent removal is the design.** The center hook has a MINIMAL tip stop — just 5mm — deliberately short so the bowstring clears cleanly on the lift-and-pull motion. Every taller hook we tried caught on the string during draw-back, scraping and clicking loud enough to spook a deer at 20 yards. This one doesn't.

**Two small side stubs, one for each hand:**
- **Release aid** on its wrist strap. Loop over the stub and it stays put. Ready when the deer walks in.
- **Hat, gloves, or ear muffs** for when the sun comes up and layers come off.
- **Paracord loop** for a face mask, kill tags, calls, or a spare glove.

The stubs are intentionally small (0.6 in reach) and low-profile — no sharp edges, no noise-catching hooks in the blind interior.

**Purpose-built for high-mount install so your bow clears the floor.**

Most drop-on blind gear is designed for chest-level or lap-level height. That works for a coffee cup or a phone — but a compound bow hung that low will drag its bottom cam on the blind floor. This hanger is designed to mount NEAR THE CEILING of your blind, on the top-downward hub poles, so a 30-inch bow hangs cleanly with the bottom cam a foot off the floor.

**Self-guiding slide install.** Both back-arm brackets have a diagonal ramp cut on their channel-facing side (angled to match typical hub blind pole angles, ~25-30 degrees from vertical). When you push the hanger up onto the poles from below, the poles ride the ramp and seat themselves in the channel on their own — no fussy alignment, no tilting the bar sideways. If your blind's poles land anywhere between 20 and 40 degrees from vertical, the slide takes it.

**Extra-wide 13-inch bar.** Fits blinds with pole spreads from tight-hub 8-inch to wide-hub 12-inch spacing at ceiling height. The 9-inch open middle channel between the two brackets means the hanger doesn't care where along the pole your ceiling hub sits — it drops on and finds its own position.

**Fits ANY pop-up hub blind with angled back poles between 1/4 in and 3/4 in (6mm to 19mm) in diameter.** No brand or model gotchas — if the pole measures anywhere in that range, this hanger fits. Ameristep, Primos, Rhino Blinds, Muddy, Barronett — all covered.

**Not for**: hard-shell permanent blinds, elevated permanent blinds, treestand-only setups without a mounted platform (needs somewhere to hook on).

**Why this design wins:**
- **Silent bow removal.** 5mm tip on the center hook clears the bowstring cleanly. No scrape, no click.
- **Self-guiding slide.** Diagonal ramp on each back arm guides the poles into the channel as you lift the bar — no wrestling, no alignment.
- **13-inch bar** fits blinds with any pole spread from 8 to 12 inches at ceiling height.
- **Split-limb compatible.** 3.9-inch center hook length covers all modern split-limb compounds.
- **Zero hardware.** Twenty-second install. No drilling, no straps, no clamps, no thumb screws.
- **Cold-stable to -20°F, UV-stable.** Wisconsin, Michigan, Minnesota-tested through November and December.
- **Made in USA**, designed and 3D printed in-house in Wisconsin.

**Install (drop-on, 20 seconds):**
1. Reach up to the top-downward hub poles inside your blind (the two poles that go from the hub center down toward the floor corners).
2. Position the hanger below the poles with the channels facing up.
3. Push the hanger straight UP. The angled slide on each back arm guides the poles into the channels automatically.
4. Release. Bar hangs from the poles. Load your bow on the center hook, release aid on the outer stubs.

To remove: pull straight down and forward. The bow slides off the center hook silently, and the bar releases the poles cleanly.

**Material:** Black outdoor-grade plastic. UV-stable, cold-stable to -20°F minimum, holds shape in a hot truck bed in July. 3D printed with 3 perimeters for structural durability.

**Dimensions:**
- Overall bar: 13.4 in wide × 6.5 in deep × 3/4 in thick
- Center hook: 3.9 in reach × 7/8 in wide × 3/4 in thick × 5mm tip (catches both parallel limbs of a split-limb bow)
- Outer stubs: 0.6 in reach × 7/8 in wide × 3/4 in thick × 5mm tip
- Self-guiding slide: angled 49 degrees from vertical, cut into each back arm's channel-facing side
- Weight: ~0.28 lb (125 g)
- Rated to 15 lbs load on the center hook
- Fits hub blind poles 1/4 in to 3/4 in (6mm to 19mm) diameter

**Save with the Bow Hunter Bundle.** Get this + our Dual Caddy (cup holder + gear pocket) for $39.99 -- versus $45.98 buying them separately. Both ship in one box. Search "Bow Hunter Hub Blind Kit" in the Sorted3D shop.