Sliding Shelf Tray for Wire Shelving, No-Drill Pull-Out Organizer for Pantry and Closet

Stop digging to the back of your wire shelf. Just slide it out.

Wire pantry and closet shelves are everywhere, and the stuff on the back half of them is a pain to reach. This sliding shelf turns a section of standard closet wire shelving into a pull-out tray. Set your coffee grinder, spices, oils, cleaning supplies or a small appliance on it, then pull it toward you when you need it and push it back when you're done.

I designed it myself after getting tired of wrestling my coffee grinder out of our pantry every morning. It's my own original design, printed to order in my shop.

WHY YOU'LL LOVE IT
• Slides out from wire shelving. Pull it forward to reach what's at the back.
• No drilling. It mounts to the shelf wires, not your walls or cabinets, so it's rental-friendly.
• Simple screw-on install. 4 wire locks fasten the slide base to the shelf wires with the included M3 hardware. It takes a few minutes and comes off just as easily.
• 1.46" raised sides help keep items from sliding off.
• Low profile. The slide base hangs only about 5/8" (16 mm) below the wire shelf.
• Printed in durable plastic as standard.
• Matte textured top hides fingerprints and gives items some grip.
• 4 widths plus custom fit, made to order in your choice of color.

HOW IT WORKS
Tool needed: a small screwdriver or hex key that fits the included M3 screws.
1. Hold the slide base under your wire shelf where you want the tray.
2. Place a wire lock over the shelf wires at each mounting point and fasten it to the slide base through the gaps between the wires with an M3 screw, washer and nut. Repeat for all 4 wire locks (see photos).
3. Snug the screws until the base is firm. Don't overtighten, since the parts are plastic.
4. Slide the tray onto the base, load it up, and pull it out whenever you need it. A short install card is included.

SIZES
All sizes are 9.45" (240 mm) long and 1.46" (37 mm) tall.
• Standard: 5.71" (145 mm) outer width, 5.52" (140 mm) inside
• +1": 6.71" (170 mm) outer width, 6.52" (166 mm) inside
• +2.5": 8.21" (209 mm) outer width, 8.02" (204 mm) inside
• +3.5": 9.21" (234 mm) outer width, 9.02" (229 mm) inside
• Custom fit: for other wire spacing or wire sizes. Message me first.
The photos show the Standard size.

WHICH SIZE DO I NEED?
• Measure the footprint (base width and depth) of the item you want on the tray.
• The base must fit inside the inside width listed above, and its depth should be 9.45" or less. Leave about 1/8" of wiggle room.
• Standard fits compact items like a slim coffee grinder or 2 small spice jars side by side. The larger sizes fit wider appliances, rows of bottles or small bins.
• Allow about 5/8" of clearance below the shelf for the slide base.
• Not sure? Send me your item's base measurements and I'll recommend a size.

COMPATIBILITY
• Fits standard closet wire shelving with 1/2" (12.7 mm) on-center wire spacing and 1/8" (3.2 mm) wires.
• Measure from the center of one wire to the center of the next. If yours is different, choose Custom fit and message me your wire spacing and wire diameter.
• Does not fit solid wood, melamine or glass shelves.
• Designed for small appliances, jars and pantry items like the grinder pictured. Not meant for heavy loads.

WHAT'S INCLUDED
• 1 sliding tray in your chosen size and color
• 1 slide base
• 4 wire locks
• 4 sets of M3 mounting hardware (screws, nuts and washers)
• Printed install card
Need extra wire locks? Message me and I'll add them to your order.

MATERIAL AND CARE
• Printed in durable plastic as standard. It's tough and heat-tolerant.
• Other colors available on request. It can soften with heat, so keep it away from heat sources and out of hot cars.
• Wipe clean with a damp cloth and mild soap. Not dishwasher safe.
• Keep away from direct heat such as stovetops, ovens and toaster vents.
• Not intended for direct food contact.

ABOUT 3D PRINTING
Each tray is printed to order, so you may see fine layer lines. That's normal and doesn't affect how it works. Colors may vary slightly by screen and filament batch.

FAQ
Will it fit my shelf?
It fits standard closet wire shelving with 1/2" on-center wire spacing and 1/8" wire. If yours is different, choose Custom fit.

Can you make one for a different shelf?
Yes. Choose Custom fit and message me your wire spacing (center to center), wire diameter and the width you want. A photo with a ruler across the wires helps. I'll confirm before printing.

How much weight can it hold?
It's designed for small appliances, jars and everyday pantry items like the grinder in the photos. If you have something heavy in mind, message me first.

Will it damage my shelf?
No. It fastens to the shelf wires with small screws. There's no drilling and no adhesive, and it unscrews to remove.

How long until it ships?
Each one is printed to order and ships in 3–5 business days. Custom fit adds a few extra days.

Questions? Send me a message. I'm happy to help you pick the right size.