Replacement 3/4" inch Stainless Steel Stabilizer Folding Cone

CoinRingUSA

Have a question about the item? Send a message.

This seller usually responds within 24 hours.

Replacement 3/4" inch Stainless Steel Stabilizer Folding Cone

Message Seller

$11.95

Please select a quantity

Item details

Material

Hardened Stainless Steel

At CoinRingUSA®, we uphold the highest standards by sourcing only the best quality material and highly skilled craftsmanship when making our coin ring tools.



* NO MORE GROOVED AND WORN-OUT CONES OR CHEWED-UP PLASTIC BEARING BALLS! *


*This folding cone made from hardened stainless steel is intended to be used as a replacement to your worn or damaged 3/4" phenolic or plastic folding cone.

This is the 4th (and largest-sized) cone in the set.


Yet another improvement over all the softer folding cones made out of phenolic or plastic, these new stabilizer folding cones are machined from wear-resistant hardened stainless steel, eliminating the need to purchase additional cones due to eventual wear-and-tear.


* The full set of 4 hardened Stainless Steel folding cones is recommended and can be seen in the link below:

https://www.etsy.com/listing/475323877/new-stainless-steel-universal-stabilizer?ref=shop_home_active_2



*The 3/4" size folding cone is used in folding Dollar and American silver Eagle-sized coins. This is the final cone to use when finishing a Morgan Dollar sized coin and also the last cone to use (with the larger-sized flat spacer provided) when you’re finished folding an American Silver Eagle-sized coin.



* WATCH AS I FULLY FOLD A MORGAN SILVER DOLLAR USING THESE NEW CONES WITH NO DAMAGE TO THE COINS’ INNER DETAIL BELOW:

https://www.youtube.com/watch?v=-XzuCCFtLn4



These Stabilizer Folding Cones are a more effective and efficient option than using the delrin bearing balls. Their design allows them to do a much better job of keeping the coin level as it’s being folded over into the reduction dies when using either a Ring Sizer Machine, an Arbor Press, or a Hydraulic Press.



To use, you simply set the coin level into your reduction die, insert an appropriate size folding cone into the beveled center punched hole, and then begin to press the coin down into the die. As you continue to fold your coin down into the reduction die, you switch to a SMALLER diameter-sized reduction die and a LARGER-sized cone (and the spacer provided if needed) to finish the coin’s folding-over process.



Below are recent reviews from clients:

--- "Quarter rings are my biggest sellers. I do large production runs of quarters, so I don't need a stuck coin slowing me down. And we all know how frustrating is can be to remove a stuck coin from one of the older cones. These are just what the doctor ordered."
Jeff Morgan and Ajax of "Jeff Morgan Designs" on Sep 15, 2016
5 out of 5 stars



--- "Awesome folding cones, so glad I purchased this set, never have to replace it"
Dan Rivera on Sep 12, 2016
5 out of 5 stars



--- "These cones are on another level. Just put plumbers tape on the cones so you don't ruin the inner detail and its golden."
Jody Pettit on Sep 9, 2016
5 out of 5 stars



* MAKE SURE TO WRAP EACH FOLDING CONE WITH TEFLON® PIPE THREAD TAPE PRIOR TO USE! *

* To use, simply wrap each stainless steel folding cone with pipe thread seal tape prior to the folding process to completely protect your coin rings' inner detail. (See the last listing photo for an example of a fully folded-over Morgan Silver Dollar made with these new cones showing the Teflon® pipe thread seal tape absorbing the metal-on-metal impact and protecting all of the inner detail.)



These new hardened stainless steel folding cones also work great with the “Stabilizer” Reduction Dies, as you end up having DOUBLE the stability of both the design of the die itself as well as the folding cone when folding over any US Quarter, US Half Dollar, Morgan/Peace Dollar, or the American Silver Eagle!



Here’s why you should buy your tools from the CoinRingUSA® Shop:

1. Each folding cone is made from high quality hardened stainless steel and is CNC-machined.

2. My customers always come first! I can always be reached through Etsy, by e-mail directly, or by leaving me a comment on my blog site.

3. The level of quality of my tools is never duplicated elsewhere.

4. The optimal degree of angle is used on these cones for folding your coins.

5. I have a passion for both making coin rings as well as creating the highest quality coin ring-making tools on the market today. That's why I've created a platform where people can go to get their questions answered about all things coin rings; as well as ask questions and even leave suggestions. Please visit my new blog site at: CoinRingBlog.com for coin ring making tips, tricks, and tool updates.

6. All of my tools are 100% guaranteed

7. Why pay a little less for inferior folding cones? Buy from CoinRingUSA® to get the highest quality tools!



*** IMPORTANT NOTE ***
You don’t need to memorize which particular size folding cone fits into which size center hole in whichever coin you are about to begin folding over. Instead, you want to pick the Folding Cone that fits into your coin’s center hole, that will also fit under the ram head on your Ring Sizing Machine, arbor or hydraulic press.

As you continue to fold your coin down into the reduction die, you simply switch to a SMALLER diameter-sized reduction die and a LARGER-sized cone (and the spacer provided if needed) to finish the coin’s folding-over process.


(Coins pictured are not included and are meant for reference only).



*** SAFETY FIRST ***

--- CAUTION! These cones are small parts and can be considered a choking hazard. Please keep away from children and pets!
--- Always wear safety glasses.
--- Keep fingers, long hair, and loose clothing away from any pinch points or open flame.
--- Make sure to anneal, (heat, then quench) the coin often as you're working it often.



•To view all of my videos on coin ring tips and tricks, subscribe to my YouTube channel by typing “CoinRingUSA” in the YouTube search box, or go directly to: youtube.com/CoinRingUSA

•To see all of the coin ring-making tools that I have to offer, please visit: CoinRingUSA.com

Thanks, and here's to your coin ring-making success!



*** Shipping:

This item will be shipped by USPS Priority Mail

Please Note for International orders: If you are ordering from outside the United States, your package may be delayed at Customs, depending on your particular country's policies for inbound U.S. shipments. You will need to inquire with your local Post Office or Mail Carrier Service for further delivery information. Customers ordering from outside of the United States are responsible for any duties, import taxes and/or brokerage fees that your country might impose upon delivery. These charges are not included in the cost of shipping and handling of your order.
At CoinRingUSA®, we uphold the highest standards by sourcing only the best quality material and highly skilled craftsmanship when making our coin ring tools.



* NO MORE GROOVED AND WORN-OUT CONES OR CHEWED-UP PLASTIC BEARING BALLS! *


*This folding cone made from hardened stainless steel is intended to be used as a replacement to your worn or damaged 3/4" phenolic or plastic folding cone.

This is the 4th (and largest-sized) cone in the set.


Yet another improvement over all the softer folding cones made out of phenolic or plastic, these new stabilizer folding cones are machined from wear-resistant hardened stainless steel, eliminating the need to purchase additional cones due to eventual wear-and-tear.


* The full set of 4 hardened Stainless Steel folding cones is recommended and can be seen in the link below:

https://www.etsy.com/listing/475323877/new-stainless-steel-universal-stabilizer?ref=shop_home_active_2



*The 3/4" size folding cone is used in folding Dollar and American silver Eagle-sized coins. This is the final cone to use when finishing a Morgan Dollar sized coin and also the last cone to use (with the larger-sized flat spacer provided) when you’re finished folding an American Silver Eagle-sized coin.



* WATCH AS I FULLY FOLD A MORGAN SILVER DOLLAR USING THESE NEW CONES WITH NO DAMAGE TO THE COINS’ INNER DETAIL BELOW:

https://www.youtube.com/watch?v=-XzuCCFtLn4



These Stabilizer Folding Cones are a more effective and efficient option than using the delrin bearing balls. Their design allows them to do a much better job of keeping the coin level as it’s being folded over into the reduction dies when using either a Ring Sizer Machine, an Arbor Press, or a Hydraulic Press.



To use, you simply set the coin level into your reduction die, insert an appropriate size folding cone into the beveled center punched hole, and then begin to press the coin down into the die. As you continue to fold your coin down into the reduction die, you switch to a SMALLER diameter-sized reduction die and a LARGER-sized cone (and the spacer provided if needed) to finish the coin’s folding-over process.



Below are recent reviews from clients:

--- "Quarter rings are my biggest sellers. I do large production runs of quarters, so I don't need a stuck coin slowing me down. And we all know how frustrating is can be to remove a stuck coin from one of the older cones. These are just what the doctor ordered."
Jeff Morgan and Ajax of "Jeff Morgan Designs" on Sep 15, 2016
5 out of 5 stars



--- "Awesome folding cones, so glad I purchased this set, never have to replace it"
Dan Rivera on Sep 12, 2016
5 out of 5 stars



--- "These cones are on another level. Just put plumbers tape on the cones so you don't ruin the inner detail and its golden."
Jody Pettit on Sep 9, 2016
5 out of 5 stars



* MAKE SURE TO WRAP EACH FOLDING CONE WITH TEFLON® PIPE THREAD TAPE PRIOR TO USE! *

* To use, simply wrap each stainless steel folding cone with pipe thread seal tape prior to the folding process to completely protect your coin rings' inner detail. (See the last listing photo for an example of a fully folded-over Morgan Silver Dollar made with these new cones showing the Teflon® pipe thread seal tape absorbing the metal-on-metal impact and protecting all of the inner detail.)



These new hardened stainless steel folding cones also work great with the “Stabilizer” Reduction Dies, as you end up having DOUBLE the stability of both the design of the die itself as well as the folding cone when folding over any US Quarter, US Half Dollar, Morgan/Peace Dollar, or the American Silver Eagle!



Here’s why you should buy your tools from the CoinRingUSA® Shop:

1. Each folding cone is made from high quality hardened stainless steel and is CNC-machined.

2. My customers always come first! I can always be reached through Etsy, by e-mail directly, or by leaving me a comment on my blog site.

3. The level of quality of my tools is never duplicated elsewhere.

4. The optimal degree of angle is used on these cones for folding your coins.

5. I have a passion for both making coin rings as well as creating the highest quality coin ring-making tools on the market today. That's why I've created a platform where people can go to get their questions answered about all things coin rings; as well as ask questions and even leave suggestions. Please visit my new blog site at: CoinRingBlog.com for coin ring making tips, tricks, and tool updates.

6. All of my tools are 100% guaranteed

7. Why pay a little less for inferior folding cones? Buy from CoinRingUSA® to get the highest quality tools!



*** IMPORTANT NOTE ***
You don’t need to memorize which particular size folding cone fits into which size center hole in whichever coin you are about to begin folding over. Instead, you want to pick the Folding Cone that fits into your coin’s center hole, that will also fit under the ram head on your Ring Sizing Machine, arbor or hydraulic press.

As you continue to fold your coin down into the reduction die, you simply switch to a SMALLER diameter-sized reduction die and a LARGER-sized cone (and the spacer provided if needed) to finish the coin’s folding-over process.


(Coins pictured are not included and are meant for reference only).



*** SAFETY FIRST ***

--- CAUTION! These cones are small parts and can be considered a choking hazard. Please keep away from children and pets!
--- Always wear safety glasses.
--- Keep fingers, long hair, and loose clothing away from any pinch points or open flame.
--- Make sure to anneal, (heat, then quench) the coin often as you're working it often.



•To view all of my videos on coin ring tips and tricks, subscribe to my YouTube channel by typing “CoinRingUSA” in the YouTube search box, or go directly to: youtube.com/CoinRingUSA

•To see all of the coin ring-making tools that I have to offer, please visit: CoinRingUSA.com

Thanks, and here's to your coin ring-making success!



*** Shipping:

This item will be shipped by USPS Priority Mail

Please Note for International orders: If you are ordering from outside the United States, your package may be delayed at Customs, depending on your particular country's policies for inbound U.S. shipments. You will need to inquire with your local Post Office or Mail Carrier Service for further delivery information. Customers ordering from outside of the United States are responsible for any duties, import taxes and/or brokerage fees that your country might impose upon delivery. These charges are not included in the cost of shipping and handling of your order.

Shipping & returns

Ready to ship in 2–5 business days
From United States
Returns and exchanges accepted

Reviews

5 out of 5 stars (1,379)

You may also like