Sabine Wren Mandalorian Gauntlets Vambraces from Star Wars Season 3 Rebels

AprilStormProps

Have a question about the item? Send a message.

This seller usually responds within 24 hours.

Sabine Wren Mandalorian Gauntlets Vambraces from Star Wars Season 3 Rebels

Message Seller

$70.00+

Please select a size
Please select a material
Please select a quantity

Item details

Handmade

Materials

PETG, ABS, TPU

These are Season 3 Star Wars Rebels Sabine Wren Gauntlets printed in either PETG or ABS (I dont work with PLA as it is not durable enough for gauntlets)

This kit comes with

Left and Right hand gauntlets (2 in total)
2x stainless steel locking pins
3x flexible TPU darts
2x Long blaster nozzles
1x Sabine Rocket, consisting of separate nose cone and tail.
1x translucent blue LED backlight buttons d

The gauntet comes in 3 sizes Small Medium or Large the sizes are based roughly on the existing Death watch and Bo Katan gauntlets.

Small 5 to 6 inch wrist.
Medium 6 to 7 inch wrist
Large 7 to 8 inch wrist.

Other sizes can be made as a custom request.

As these are designed to be screen accurate as possible it means they are a rather short gauntlet compared to others as this is how they appeared in the movie, please be aware. (the medium is about 16cm long)

The design uses a 2mm locking pin,2mm bicycle spoke to close the clam, the other side latches in to give you as close to screen accurate as possible as there are no visible hinges.

The darts are printed in a flexible rubber like material, (TPU) so they will not break off if they snag

The Backlight buttons are printed in translucent blue plastic so you can place LEDS in the gauntlet to light the buttons up (LEDs are not supplied)

You can choose between ABS plastic or PETG plastic. PETG is stronger but is harder to sand and will not bond with Acetone and regular modeling plastic cements. You need to use acrylic glue for PETG. ABS is harder to print in but is generally much easier to work with. Both plastics are high temperature plastics so they will not warp in a hot car like PLA.
These are Season 3 Star Wars Rebels Sabine Wren Gauntlets printed in either PETG or ABS (I dont work with PLA as it is not durable enough for gauntlets)

This kit comes with

Left and Right hand gauntlets (2 in total)
2x stainless steel locking pins
3x flexible TPU darts
2x Long blaster nozzles
1x Sabine Rocket, consisting of separate nose cone and tail.
1x translucent blue LED backlight buttons d

The gauntet comes in 3 sizes Small Medium or Large the sizes are based roughly on the existing Death watch and Bo Katan gauntlets.

Small 5 to 6 inch wrist.
Medium 6 to 7 inch wrist
Large 7 to 8 inch wrist.

Other sizes can be made as a custom request.

As these are designed to be screen accurate as possible it means they are a rather short gauntlet compared to others as this is how they appeared in the movie, please be aware. (the medium is about 16cm long)

The design uses a 2mm locking pin,2mm bicycle spoke to close the clam, the other side latches in to give you as close to screen accurate as possible as there are no visible hinges.

The darts are printed in a flexible rubber like material, (TPU) so they will not break off if they snag

The Backlight buttons are printed in translucent blue plastic so you can place LEDS in the gauntlet to light the buttons up (LEDs are not supplied)

You can choose between ABS plastic or PETG plastic. PETG is stronger but is harder to sand and will not bond with Acetone and regular modeling plastic cements. You need to use acrylic glue for PETG. ABS is harder to print in but is generally much easier to work with. Both plastics are high temperature plastics so they will not warp in a hot car like PLA.

Shipping & returns

Ready to ship in 2–3 weeks
From Australia
Shipping upgrades available in the cart
Returns and exchanges accepted
Exceptions may apply.

Reviews

5 out of 5 stars (515)