Whoa! You can't favorite your own shop.

Whoa! You can't buy your own item.

Whoa! You can't favorite your own item.

Whoa! You can't add your own item to a list.

Add this item to a treasury!

You don't have any treasuries yet. Enter a title below to create one.

This item has been added.

View your treasury.

Like this item?

Add it to your favorites to revisit it later.
Request a custom order and have something made just for you.
The pictured ring was made using Leadwood with accents of golden Koa and an inlay of crushed Malachite stone. This listing is for a similar ring custom made to your size. It will be made using the "bent wood method" for durability.
For those who are not familiar with wooden rings, it is helpful to understand that there are two general methods for making them. I will call them the “block method” and the “bent wood method.” The “block method” involves layering the different woods into a little block. Then, the hole is drilled out and the ring is shaped from that. This is a fairly quick way of making rings, so I can do it relatively inexpensively. If done properly, it still makes for a nice ring.

The “bent wood method” involves taking thin strips of the main wood and heat/steam bending them into circles. These are then layered to themselves and the ring can be shaped from that. When desired, a groove can be cut around the ring and other woods or even crushed stone can be inlaid. This is a much more tedious process and is a bit more expensive. However, because the grain of the wood runs all the way around the ring, this method produces a much stronger ring.

If you are on a tight budget and aren’t planning on wearing your wooden ring every day, the “block method” may be the best choice for you. But if this is going to be your wedding band and are planning on wearing it constantly, or if the cost isn’t an issue for you, I recommend the “bent wood method.” The added quality of the ring is worth the extra cost.
If you see a ring of mine that was made using the “block method” and would like a similar ring in the “bent wood method” (or vice versa), let me know and I will provide a listing for you to purchase.

When shopping for a wooden ring and aren’t sure which method was used, ask the seller so that you know what you are getting. This specific listing is for a "bent wood" ring.
In order to protect the wood and insure a long life for the ring, I finish each of my rings with multiple coats of a Cyanoacrylate finish (basically a highly refined superglue). After testing many different finishes, this is what I’ve found to be the most durable and longest lasting. I am happy to use a different finish upon request. If at any time, the finish on your ring becomes damaged, simply return the ring to me and I will refinish it for $3 (to cover the cost of shipping back to you).
US ring sizes typically range from 1-15. If you don’t know your size, it is recommended that you visit any jewelry store before ordering to get professionally sized. There are other methods of measuring available, but I have often found them to be inaccurate. Since wooden rings cannot be resized, it is important to get an accurate measurement. Keep in mind that I can make rings in ¼ and ½ sizes, as well.

During checkout, there will be a section where you can write me a note. Just let me know there what size you will be needing, as well as any other customizations that you would like.
If after receiving your ring, you determine that you need a different size, return the original back to me and I will make an exchange with you for $5, which covers my materials cost and shipping.
If you would like to speak with me before ordering, please send me a message here on Etsy or email me at MnMWoodworks [!at] gmail.com. I am always happy to customize my rings for you, using different woods or stones of your choice.
My rings are carefully crafted and take a considerable amount of time to make. Please allow one to two weeks for me to get your ring made and finished before shipping it out.
Each ring is made using materials in their natural state. I use no dyes, stains, or other colorings. The colors you see in my rings are the colors that are found in nature and will often vary somewhat from ring to ring.

Wooden Ring or Wedding Band with Stone Inlay (Bent Wood Method)


  • Handmade item
  • Materials: wood, leadwood, koa, malachite, stone
  • Made to order
  • Ships worldwide from United States
  • Feedback: 544 reviews
  • Favorited by: 212 people