Multi-meat Flower Pot Concrete Silicone Mold: Large Pen Tube eramic Plant Pot Epoxy Resin Mold

Mold size: 8.5 * 8.5cm
Please note: This does not include the black outer casing that comes with the product.


Etglue production method:
1, soft crystal adhesive (soft product will be soft) method:
l Prepare the container used and clean and dry molds.
2 Two sets of A and B of the crystal rubber needed to be weighed with 3: 1, and the group A was heated to about 40 ° C and then added to the group B, poured into the container, stir well, and gas bubble.
3 After defoaming the glue, the debris or syringe, etc., such as the mold edge crystal glue, can not be used, can be used to move the glue to the surface.
4 Gel curing: The mold is applied, the gel time is approximately 25 ° C for 3 hours; the curing time is about 36 hours. Or put the coated mold in a constant temperature drying tank of 60 ° C, completely cured for 3 hours. .
2, hard thermal crystal glue (hardware) method of operating:
1 Prepare the same before the configuration.
2 After the Crystal Grid of the desired crystal gum is 3: 1, stir well, it can be dried on the mold.
3 gel solid: Apply a good sign to the oven at 60 ° C for 1.5 hours; or place it for about 13 hours at room temperature.


Cement production tutorial
1: With cement, water, quartz sand, stir well, fell to mold, cool one day, become dry, can be used in demolding plastering mortar
2: Ultra High Strength Cement + Water Orkem + Water
3: Pure Cement + Quartz Sand + Water OR Pure Cement + fine sand + water
4: If you want to have a color pot, add iron oxide pigments. What color is used to use the iron oxide of the pigment, or add a different color of the water grinding glass stone decoration is also a good choice.
5: Gypsum can also, with gypsum + water, gypsum and water ratio is 3: 1, stirred down the mold, dry, dry, can be placed or drawn.
6: The agitation ratio is different according to the situation of each person. The ratio of cement and sand is between 1: 1-1: 3. The proportion of cement and water is between 1: 0.4-1: 0.7, the sand is not absorbed, the cement mixed with the sand is calculated to calculate the water of the cement. If it is not sand, the drying process shrinks too large and is easy to crack.
7: The cement is filled with the mold, then shakes the bubble, stand on a day and night, you can touch it is very dry, thoroughly dry, just overweight, slightly dragged out. This is released, and if you worry that it is difficult to brush a layer of glycerol or lubricant in the mold so that it is easier to release.
It is recommended to use 42.5 cement, sand to choose from sand or quartz sand. 52.5 Cement 8-12 hours demould release, 42.5 cement 20-24 hours demold, 32.5 cement more than 24 hours or more mold release, rain, and dual wet environment demolding time doubled. The thicker the mold, the longer it ~


* · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · ** · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * · * ·

Express selection registration express, time limit is generally around 10 to 20 days
Come because the express delivery of the epidemic may slow down, please understand, thank you.
If so, please contact: luowenjun2018 [!at] outlook.com ^ _ ^