Custom Phone Mount for 2022-2026 Honda Civic, 2023-2026 Honda CR-V, Accord, Acura Integra, & 2025+ Honda Prelude

This is a custom-fit 3D-printed phone mount that securely attaches to the ‘honeycomb’-style HVAC vents in all 2022 to 2026 Honda Civic, 2023 to 2026 Honda CR-V and Accord, 2023 to 2026 Acura Integra, and 2025 and up Honda Prelude models. It features a 3D-printed adapter which is designed to be ‘wedged’ into the small gaps between the HVAC vents and their plastic surround, allowing for a secure and stable fit while being easily removable. The adapter can be positioned anywhere along the driver or passenger HVAC vents, allowing flexible orientation based on your preference. It also features a 17MM-diameter pivot ball end for easy attachment to most automotive phone holders, 4 styles of which can be bundled with the adapter for a complete solution. This design eliminates the guesswork of universal mounts that may not properly fit your vehicle, offering a clean, adjustable solution that installs in seconds.

Check out the same style of mount for your Honda HR-V or Acura ADX with 'honeycomb' vents HERE: https://www.etsy.com/listing/4571668909/custom-phone-mount-for-2023-2026-honda

Compatibility:
• 2022-2026 Honda Civic
• 2023-2026 Honda Accord
• 2023-2026 Honda CR-V
• 2023-2026 Acura Integra
• 2025+ Honda Prelude
• Fits ONLY in the HVAC vent bezels in these models and year ranges; will NOT fit in other Honda / Acura models (HR-V, etc.) with similar ‘honeycomb’-style vents due to sizing differences!

Attachment Options:
• 3D-printed adapter ONLY, you supply your own 17MM-compatible phone mount
• Adapter with full-body plastic 'standard' mount
• Adapter with basic magnetic mount and adhesive metal sheets (NOT MagSafe compatible)
• Adapter with MagSafe-compatible ring mount (ONLY compatible with MagSafe devices / cases)
• Adapter with MagSafe charger mount (ONLY compatible with MagSafe devices / cases, supports 15W charging, plugs into USB-A port)
** The exact appearance and cable color of the optional MagSafe-compatible wireless charger may vary between the 3 styles pictured in the listing depending on availability. All charger styles have been tested to reliably fit and work with this mount’s 17MM pivot ball attachment. **
• Keep in mind that the MagSafe ring and charger mount styles will only work with phones/cases that are MagSafe compatible – if your device / case does not allow for this, then only the standard plastic and basic magnetic mounts will work.
• The basic magnetic mount will NOT support larger phones (> 200g) or thicker cases (> 1mm) due to limitations in strength of the included sheets.
• If you decide to order any of the 4 styles of mounts with the printed adapter, please be aware of their compatibility and strength, and be sure to test the assembled mount can securely hold your phone BEFORE driving with it. These are 3rd-party components that are handpicked, tested, and assembled with our handmade parts, but they are not manufactured by us. We will NOT be responsible for any damages resulting from their installation, use, or misuse.

Installation Guide:
• Take the 3D-printed adapter piece and, with the ball end angled downwards, wedge the bottom prong into the gap between the vent and the lower lip of the surrounding trim piece at the location where you’d like the mount to be installed.
• Then, press down on the upper prong to compress it and pivot it inwards towards the face of the vent. Once the upper prong is positioned around where the gap is between the vent and bezel, you can release the tension on it, so it flexes upwards to wedge into the opposing trim gap. Ensure the bottom prong doesn’t pop out of the gap it’s already been seated in, and that you’re applying enough pressure on the top prong so that it doesn’t scratch the vent bezel while mounting.
• You may need to apply light additional pressure on the face of the vent itself and/or on the upper or lower prong to make sure the adapter is fully wedged into the gaps. You can then lightly shake and pull on the adapter to make sure it is secure.
• Install the phone mount onto the pivot ball end of the adapter by unscrewing the fastening nut from the back of the mount, slipping the nut over the round ball end of the adapter, pressing the mount on to the ball, and then tightening the nut down on the back of the mount by rotating it counterclockwise (since the mount is facing towards you).
• IMPORTANT: ensure you properly loosen the fastening nut on the phone mount BEFORE attempting to rotate or adjust it. If the nut is still tightly attached and you attempt to rotate it, you will risk bending or breaking the 3D-printed adapter piece. Simply unscrew the nut to rotate and adjust, then re-tighten it when you have the mount in the most comfortable spot. I will NOT provide free replacements for broken adapters due to improper installation / adjustment of the phone mount.
• You can remove or relocate the adapter piece at any time by inversing the steps outlined above; remove the phone mount from the ball end by unscrewing the nut and then pulling the assembly off, then the adapter is removed by compressing the top prong to pivot it out of the gap, after which the bottom prong can be angled and pulled outwards.

Materials:
• ASA plastic for stiffness, strength, and resistance to both extreme heat and UV degradation

Lead Time & Shipping:
• Up to 7 days for processing, printing, and shipping
• Domestic shipping in the USA via USPS Ground Advantage
• International buyers are responsible for all shipping, customs, and import fees

Returns:
• Must be initiated within 30 days of receipt for UNUSED and UNDAMAGED parts only

Thanks so much for your interest! Feel free to message me with any comments, questions, or feedback and I will get back to you as soon as possible!