Gel Coated Ford emblem overlays American Flags(and other styles):F-150 ,Super Duty, Taurus SHO,Explorer,Escape,Fiesta, Fusion, Focus & Edge

***LET US KNOW IF YOU NEED A SIZE FOR A DIFFERENT MODEL BY SENDING US A MESSAGE OR REQUESTING A CUSTOM ORDER****

**PLEASE NOTE: Some factory Ford emblems have an embossed or raised Ford logo molded into them. This will show through your vinyl overlay once the overlay is installed and the vinyl conforms to the surface of the emblem. This look is much more noticeable with the non-domed wrap overlays (and this look is usually preferred by most people). The thicker, domed overlays will allow the show-through much less, but it still will be noticeable, especially when viewed up close. This can only be avoided by grinding down the factory emblem first using a Dremel tool or perhaps a detail sander. Keep in mind that if you do decide to grind the emblem, it will cause permanent damage and may be a factor if you ever remove the overlays and sell the vehicle, etc.

To find the size you need. simply measure the BLUE area of your factory grill and tailgate/rear hatch/trunk emblems. It is important to confirm the size you need, especially if you purchased your vehicle used, as sometimes the previous owner has swapped out the emblems, grills or entire tailgates for one from a different year. See below info for help in sizing:


Wheel center caps = 1in x 2.75in (message us if you a need diff size)
* Sold in sets of (4)

Steering wheels (most years/models, but measure to confirm) = .875in x 2.25in

SUPER DUTY:

-1999-2004 Super Duty GRILL emblems = 2.375in x 6.3in
-1999-2004 Super Duty TAILGATE emblems = 2in x 5in
-2005-2010 Super Duty GRILL emblems = 3.2in x 8.2in
-2005-2010 Super Duty TAILGATE emblems = 3.2in x 8.2in
**NOTE: if your vehicle has the factory back-up camera inside the rear emblem, you will need a 2.375in x 6.3in size overlay. Measure to confirm!**
-2011-2016 Super Duty GRILL emblems = 4.56in x 12in
-2011-2016 Super Duty TAILGATE emblems = 3.2in x 8.2in
**NOTE: if your vehicle has the factory back-up camera inside the rear emblem, you will need a 2.375in x 6.3in size overlay. Measure to confirm!**
-2017-19Super Duty GRILL & TAILGATE emblems = 4.125in x 10.875in
**NOTE: If you have a Platinum, Limited or King Ranch, tailgate emblems are smaller (1.75in x 4.625)

F150:

-2006-2014 F-150 GRILL and TAILGATE emblems = 3.2in x 8.2in
**NOTE: if your vehicle has the factory back-up camera inside the rear emblem, you will need a 2.375in x 6.3in size overlay. Measure to confirm!**
-2015+ F-150 GRILL and TAILGATE (except Platinum) emblems = 3.312in x 8.625in
** F-150 Platinum, Limited or King Ranch edition will require a 1.75in x 4.625in tailgate emblem overlay. Measure to confirm!**

The sizes in the drop-down menus may fit many other models as well...just measure the BLUE area to find out!

Escape 2008-19
*2.375in x 6.3in (Front); Rear 2in x 5.15in(Rear)

Focus:
*2012-14 = 2.437in x 6.375in (Front); 1.875in x 4.937in (Rear)
*2015+ = 1.5in x 4in (front and rear)

Explorer:
*2006-10 = 2.375in x 6.3in (front & rear)
*2011-2015 = 3.2in x 8.2in (front); 2.375in x 6.3in (rear)
*2016-19= 3.2in x 8.2in (front); 2.5in x 6.3in (rear)

Taurus SHO
*2010-12 = 2.375in x 6.3in (front & rear)
*2013+ = 1.95in x 4.95in (front); 2.15in x 5.45in (rear)

Fusion:
*2010-2014 = 2.375in x 6.3in (front); 2in x 5in (rear)
*2015+ = 1.5in x 4 (front); 1.75in x 4.625in (rear)

Fiesta:
*2015+ 1.5in x 4in (front & rear)

Edge:
*2007-15: 3.2in x 8.2in (front); 2.375in x 6.3in (rear)
*2016+: 3.2in x 8.2in (front); 1.75in x 4.625in (rear)

These are flexible, vinyl *OVERLAYS* that are designed to install over your factory Ford emblems- the factory emblems are NOT included- sorry!

How hard are these to install? Not hard at ALL! Why? Because this very high-tech, specialty vinyl allows you to position the overlay and then lift it back up if you need to- again and again and again until you apply pressure and make it "permanent"! Install them DRY with no worries!! When you want to remove it- simply heat it up (hair dryer works fine if you do not have a heat gun) and peel it off. AND it's removable up to 4yrs without leaving any residue or adhesive behind!

Durable, dimensionally stable, vinyl film with positionable, pressure activated adhesive (permanent, changeable or removable) that allows it to be repositioned on the application surface during installation. Special channels allow trapped air to escape, which reduces air bubbles that typically occur as large format graphics are installed.

*********************************************************
Please email us with any questions: DeVriesSigns [!at] gmail.com. Ask about our other products: DOMED Ford oval emblem overlays: DOMED wheel center cap emblem overlays; DOMED WeatherTech/Husky liner emblem overlays; Ecoboost (ecobeast) emblem overlays: GMC emblem overlays: Chevy bowtie emblem overlays.

FOLLOW US ON INSTAGRAM @ DeVries_Designs !!